Metal Roofing in Rockaway, NJ
Rockaway Roofing Pros installs metal roofing that sheds heavy snow, shrugs off spring hail, and outlasts the freeze-thaw cycles that work on every rooftop in Morris County. We begin with a full roof inspection, then price a standing-seam panel or an exposed-fastener panel against your pitch, deck condition, and budget. Call 9736364945 for a free roof estimate and a written line-item scope.
Call 9736364945Metal roofing is panel work, and the panel you choose decides everything downstream. A standing-seam panel hides its fasteners under a folded seam, so nothing sits on the surface to back out or leak.
An exposed-fastener panel costs less and installs faster, but each screw rides on a neoprene washer that cracks with age. A corrugated panel is the oldest profile in the trade and still works on outbuildings.
Stone-coated steel and aluminum mimic wood shake, cedar shake, slate, clay tile, or concrete tile without the weight.
We install McElroy Metal, ATAS, and Decra products and talk through gauge, finish, and PVDF versus SMP coating before you sign anything.
Every job starts with a tear-off to the roof deck. We replace rotted plywood or OSB sheathing so the substrate sits flat, then build the layers in order.
A self-adhered ice-and-water shield goes at the eave and in every valley, with synthetic underlayment over the field. Drip edge, rake trim, and hip and verge trim go down before the panels.
Old roofing felt, tar paper, and asphalt shingles leave in a dumpster we park on site.
Low-slope sections get TPO, EPDM, or a PVC membrane. We also repair built-up roof, modified bitumen, and tar-and-felt assemblies that pond or blister.
A parapet, scupper, or coping cap needs its own flashing detail, because flat roofing fails there first.
Underneath, insulation, a vapor barrier, and ventilation matter most, since warm wet attic air rots a deck from the inside.
A gambrel or mansard roofline, a canopy or awning over a side door, and a deep overhang all change how water leaves a roof. So does the pitch.
Rockaway snow load, ice dam growth at the eave, and spring hail test every detail. A snow guard above a doorway keeps a slide off your steps.
We anchor every fastener and screw to the manufacturer's pattern and the local building code.
Our crew works from a ladder, scaffold, or safety harness and strips the old roof with a nail gun, pry bar, and roofing shovel. We check the layout with a roofing square and seal the last joints with mastic or roof cement.
What's Included
Our Metal Roofing Process
What Our Metal Roofing Process Looks Like, Step by Step
- We run a roof inspection from the ladder and from the attic, checking decking, trusses, rafters, joists, and the ridge beam for rot or sag.
- You receive a line-item roof estimate that separates labor, panels, underlayment, flashing, and any decking repair, so you know what each dollar buys.
- We order to the measured square count, and a dumpster lands in the driveway the morning the tear-off starts.
- The crew strips the old roof, replaces bad sheathing, and sets the substrate flat before a single panel goes down.
- On a standing-seam panel we set purlins, battens, or counterbattens where the design calls for them, then lock panels in staggered courses.
- We lay ice-and-water shield and synthetic underlayment, then install the starter course, drip edge, and valley flashing.
- Fasteners, screws, and clips get set at the correct depth and never overdriven, and each detail is hand-sealed with roof cement.
- We finish the ridge cap, ridge vent, and pipe boot, then sweep the lawn and the gutter for debris and walk the roof one last time with you.
Free Inspection
We assess your roof with a thorough inspection and provide a detailed photo report — no cost, no obligation.
Clear Estimate
You get an itemized scope with materials, labor, and timeline. No hidden fees. We discuss insurance and financing options.
Expert Work
Licensed crews arrive on schedule, protect your property, complete the work, and clean up thoroughly.
Final Walkthrough
You inspect with us. We document everything with before/after photos. Warranty registered and paperwork delivered.
Signs You Need Metal Roofing
Warning Signs You Need Metal Roofing Instead of Another Patch
- Granule loss on the old asphalt shingle, where bare asphalt and bitumen show through and the mat begins to erode.
- Ice dam ridges along the eave after a heavy snow, which means meltwater is backing up under the shingles and into the soffit.
- Dents, bruises, or punctures from spring hail, especially on softer aluminum panels or older metal roofing that has oxidized.
- Rust streaks, chalking, or a coating that has started to flake and peel on a panel that should still have years left.
- Loose or backed-out fasteners on an exposed-fastener panel, where each screw depends on a washer that can crack.
- Ponding water in a valley or on a flat section, where a membrane, modified bitumen, or built-up roof has settled and sagged.
- Daylight or damp framing near a skylight, dormer, or chimney, which usually means failed flashing rather than a panel problem.
- Sealant and caulk repairs every year, which signals end-of-life wear on a roof past its service window.
Metal Roofing — Frequently Asked Questions
How much does metal roofing cost, and what drives the number?
Metal roofing is priced by the square, and the panel type drives most of the difference. Standing-seam steel costs more than an exposed-fastener panel because of the folding and the hidden clips. Deck repair, pitch, and penetrations move the number too.
How long does a metal roofing installation take?
Metal roofing usually takes longer than a shingle tear-off, often several days to a couple of weeks once materials are staged. A simple gable goes faster than a roof with dormers or a mansard section. Morris County weather can add days.
Does metal roofing hold up to Rockaway snow and hail?
Metal roofing handles snow load and hail better than most alternatives when the panels are fastened correctly. A smooth standing-seam panel sheds snow, which limits ice dam growth at the eave. Hail can still dent aluminum, so we talk gauge first.
Will my insurance cover damage to an existing metal roofing system?
Metal roofing claims depend on the cause and the age of the existing roof. We photograph the damage, meet your adjuster on site, and write a line-item estimate that matches the insurance scope. If the carrier underpays, we help file the supplemental claim.
Can you install metal roofing over my existing shingles?
Metal roofing can sometimes recover over existing shingles, but only when the deck is sound and the building code allows it. We prefer a full tear-off when there is rot, decay, or trapped moisture. An overlay hides a problem you pay for later.
What maintenance does a metal roof need each year?
Metal roofing needs less maintenance than asphalt shingles, though not none. Once a year we check fasteners, sealant, and flashing, clear debris from valleys and behind the chimney, and reseal any joint that has opened. Clean gutters protect the fascia.
Don't just take our word for it — hear from our satisfied customers.
Dana R., White Meadow Lake: "We had ice dams three winters running, so we switched to a standing-seam panel. The crew tore off the old shingles, replaced two rotted sheets of sheathing, and snow slides right off now."
Tom K., Marcella: "Spring hail dented our old aluminum roof. They walked me through gauge and finish options, answered the phone when I called, and left the driveway cleaner than they found it."
Priya S., Lake Telemark: "Water was wicking past the chimney flashing into the attic. They retied the counter-flashing, resealed the pipe boot, and showed me photos of the fix before they packed up."
Ready to get started? Call us today at 9736364945 for a free estimate.
Free estimates · Licensed & Insured certified · up to 50-year warranty
Call 9736364945
